Description

The EtherNet/IP Adapter firmware implements all CIP objects and services to build an EtherNet/IP Adapter device that can pass ODVA's conformance test.
This in addition requires a correctly behaving host application that interfaces to the firmware through the Dual Port Memory (DPM) interface.

Configuration

The stack can be configured via data base files (generated with Hilscher's Sycon.net or Communication Studio) or via the DPM's mailbox interface (refer to the corresponding API manual).
During connection establishment to an EtherNet/IP Scanner (PLC), it is possible to pass configuration data to the host application.

Implicit Messaging (Cyclic Data)

Through the DPM the host application has access to the process data that is consumed and produces by the firmware.

Explicit Messaging (Acyclic Data)

Acyclic services received from the network and addressing 'build in' CIP objects (CIP objects that are part of the firmware's default CIP object model) are handled by the firmware itself.
There is the possibility to extend the default object model by additional CIP objects, e.g. to support CIP profiles or vendor specific CIP objects.

Key Features

Cyclic I/O data (Implicit Messaging): class 0 / class 1
Acyclic data (Explicit Messaging): Unconnected / Connected (class 3)
Connection Application Types: Exclusive Owner, Input Only, Listen Only
Trigger Types: Cyclic, Change of State, Application Triggered
Device Level Ring (DLR) - Media Redundancy ¹⁾
Address Conflict Detection (ACD)
Quality of Service (QoS)
CIP Sync ¹⁾
QuickConnect (Fast Startup)
NULL-ForwardOpen
CIP Safety "Ready" (provides all necessary features and interfaces to attach a CIP Safety stack on top)
Firmware built-in CIP Object model can be extended by additional CIP objects (e.g. to support CIP profiles)

Supported Protocols

TCP/IP, UDP/IP
DLR ¹⁾
DHCP / BOOTP
IEEE 802.3
IEEE 802.1Q
LLDP
SNMP
PTP (Precision Time Protocol) ¹⁾

Technical Data

The technical data of the individual available firmwares differ slightly. Therefore, the below table only provides a rough overview of the supported features.

Note: For a detailed listing of the technical data, please refer to the data sheet of the individual firmware. You can find them in the "Resources" section on the specific firmware version page.

Firmware data sheets are available for version V3.8.0.0 and higher.

Feature	Description
Maximum number of input data per assembly instance	504 bytes
Maximum number of output data per assembly instance	504 bytes
Maximum number of assemblies (firmware dependent)	10
IO Connection Types (implicit)	Exclusive Owner, Listen Only, Input only
IO Connection Trigger Types	Cyclic, minimum 1 ms* Application Triggered, minimum 1 ms* Change Of State, minimum 1 ms*
Explicit Messages	Connected (class 3) and unconnected
Unconnected Message Manager (UCMM)	supported
Max. number of connections (firmware dependent)	Class 0 / Class 1: 5 Class 3: 10 UCMM: 10
Max. number of user specific objects (firmware dependent)	20
Predefined standard objects	Identity Object (0x01) Message Router Object (0x02) Assembly Object (0x04) Connection Manager (0x06) DLR Object (0x47) ¹⁾ QoS Object (0x48) TCP/IP Interface Object (0xF5) Ethernet Link Object (0xF6) LLDP Management Object (0x109) Time Sync (0x43) ¹⁾
DHCP	supported
BOOTP	supported
Baud rates	10 and 100 MBit/s
Duplex modes	Half Duplex, Full Duplex, Auto-Negotiation
MDI modes	MDI, MDI-X, Auto-MDIX
Data transport layer	Ethernet II, IEEE 802.3
Address Conflict Detection (ACD)	supported
DLR (ring topology)	supported ¹⁾
Integrated switch	supported ¹⁾
CIP Reset services	Identity Object Reset Service of Type 0 and 1

Browser not supported