Introduction

This Application note explains, how to configure a generic modular adapter, when the entry for "ProxyConnect" is not described in the Ethernet/IP Slave Device Description (EDS).

Please refer to the following FAQ: "Why does my modular EDS file not work?" → https://hilscher.atlassian.net/wiki/pages/viewpage.action?pageId=113541135

As an example the Allen Bradley Point I/O Module Adapter "1734 AENT" is used, together with the fitting Point I/O Modules "1734 IB8" and "1734 OB8E".

Hardware configuration

Slot	Module Name	EDS File
0	1734-AENT	0001000C006C0300.eds
2	1734-IB8	0001000700D80300.eds
3	1734-OB8E	0001000700DA0300.eds

The EDS File of each module is needed for further configuration of the Generic Modular Adapter.

These can be found on the Rockwell Automation Page:

https://www.rockwellautomation.com/de_DE/detail.page?pagetitle=Electronic-Data-Sheets&content_type=overview&docid=11432fc64a2a887b85011582be53806b

Software Configuration

Add Modules

In SYCON.net, add an EtherNet/IP Scanner (e.g. CIFX RE/EIM) and then an ENIP Modular Generic Adapter to the network.

Open the Configuration Window of the Modular Generic Adapter and choose "Module" in the Navigation Area.

Change “Slots in Rack” to "4" and add the modules.

Since 1734-AENT covers 2 Slots, skip one slot between 1734-AENT and 1734-IB8:

Configure 1734-IB8

Specify Connection

EtherNet/IP is a connection-oriented protocol, therefore the connection should always be specified first.

Open the EDS for 1734-IB8 and go to the section [Connection Manager], assuming that Connection23 (Input only) will be used:

Configure connection settings

Please choose "Connection" in the Navigation Area of the Modular Generic Adapter. Select the Module “Slot<1> 1734-IB8”.

Decode the fields "trigger & transport" and "realtime format", which are defined in Connection23.

These parameters describe the connection variables, which have to be filled in the Connection configuration window in Sycon.net.

The free Tool "EZ-EDS" from ODVA (https://www.odva.org/software/EZ-EDS-Download), can be used to decode the parameters easier.

Therefore, open the EDS by selecting "File → Open…”. Select "Generic EDS" as EDS type and ignore the upcoming error messages.

When the file is successfully opened, select “Connection1” in the left tree view.

The name “Connection23” in EDS file is automatically converted to “Connection1”.

Configure the Connection Area in Sycon.net, based on the shown informations:

Don't forget, to set the Connection name to "Connection23".

Configure assembly instance ID

Choose "Assembly" in the Navigation Area of the Modular Generic Adapter now. Select the Module “Slot<1> 1734-IB8”.

Now the Connection Path has to be filled in. The Connection Path is described in Connection23 in the EDS-File:

Switch back to EZ-EDS, select “Connection1” in the left tree view.

Click the Button "Decode Path". A new Window will pop up. Select decimal format in this dialog.

Now the instance ID can be read out for Configuration in Sycon.net.

Based on the above informations, the assembly Instance ID can be specified:

The instance "20 04 24 67 2C BE 2C 04" can also be decoded manually as follows:

20 04

24 67

2C BE

2C 04

Logical Segment,

Class ID 0x04(4)

Configuration path,

instance ID 0x67 (103)

O2T Connection Point,

output Assembly instance ID 0xBE (190)

T2O Connection Point,

input Assembly instance ID 0x04 (4).

Configure Input assembly length

The input assembly length is defined in the field “T->O size” and field “T->O format” of Connection23:

It can be decoded as follows:

T → O

, , Assem127

RPI	Size	Format
empty	empty	Assem127

When the "Size" of the T=>O default description is empty, the format has to be evaluated.

In this case, Assem127 is used to define the format. Go to the definition of Assem127, in the EDS.

Since the field for the length is empty ($ Length in bytes), the Member fields should be evaluated:

The Assemblys Members can be decoded as follows:

,,

32,,

,Assem4;

	Member Size	Member Reference
1st Member	empty	empty
2nd Member	32	empty
3rd Member	empty	Assem4

This means, the first Member is reserved, the second one has a size of 4Byte (32Bit) and the third one references to Assem4.

Go to Assem4:

The "total length in bytes" is defined as "1".

Now the total size of Assem127 can be defined:

	Member Size	Member Reference	Size in Byte
First Member	empty	empty
Second Member	32	empty	4
Third Member	empty	Assem4	1
Total length of Input Assembly Assem127			5

Configure Output assembly length

The output assembly length is defined in the field “O->T size” and field “O->T format” of Connection23:

It can be decoded as follows:

O → T

,0,,

RPI	Size	Format
empty	0	empty

Since the field “O->T size” is not empty, it can directly be read – 0 Byte.

In this case no further evaluation is needed.

In case this field is refered to a Parameter or Assembly, please use the steps mentioned in the example above: "Configure Input assembly length".

Configure configuration assembly length

The configuration assembly length is automatically calculated by the data length of the cfg. #1 and cfg. #2 data segment.

The user is not allowed to directly edit this length.

Configure cfg. #1 data segment

The cfg #1 data segment is defined in field "$ config part 1" of Connection23:

Here Assem124 is used to define the format. Go to the definition of Assem124:

In this case, both Values ("Member Size" and "Member Reference" have to be evaluated.

The Assemblys Member informations can be read as follows:

	Member Size	Member Reference
1st Member	16	Param101
2nd Member	16	empty

The field of the first Member indicates, that it has a data length of 16 bit. It also has a Reference to Param101.

Go to the definition of Param101.

The "data size in Byte" has a size of 2 Byte, with a default value of 1.

Therefore the default data of Param101 is 0x0001.

The user can also define a value between min. value and max. value.

Go back to the definition of Assem124, the Second Member has a length of 16 and has no Reference entry. This means, it's defined with value 0.

	Member Size	Member Reference	Data (Hex)	Swap
1st Member	16	Param101	01 00	01 00
2nd Member	16	empty	00 00	00 00
Total				01 00 00 00

Configure cfg. #2 data segment

The cfg #2 data segment is defined in field "$ config part 2" of Connection23:

Here Assem103 is used to define the format. Go to the definition of Assem103:

This Assembly has a few more Members.

Please repeate the procedure mentioned in the first data segment for each Member.

For example the first Member:

The Size of this Member is definded with 16 Bit and has a Reference to Param9.

Param9 has a size of 2 Bytes, the Default Value is 1000 (Hex 03E8):

When analyzing all Members and Parameters, the following table can be created:

Member	Member Size	Member Reference	Data (Hex)	Swap
1	16	Param9	03 E8	E8 03
2	16	Param10	03 E8	E8 03
3	16	Param11	03 E8	E8 03
4	16	Param12	03 E8	E8 03
5	16	Param13	03 E8	E8 03
6	16	Param14	03 E8	E8 03
7	16	Param15	03 E8	E8 03
8	16	Param16	03 E8	E8 03
9	16	Param17	03 E8	E8 03
10	16	Param18	03 E8	E8 03
11	16	Param19	03 E8	E8 03
12	16	Param20	03 E8	E8 03
13	16	Param21	03 E8	E8 03
14	16	Param22	03 E8	E8 03
15	16	Param23	03 E8	E8 03
16	16	Param24	03 E8	E8 03

Therefore the cfg #2 data segment results in:

E803 E803 E803 E803 E803 E803 E803 E803 E803 E803 E803 E803 E803 E803 E803 E803

Final assembly configuration of 1734-IB8

Configure 1734-OB8E

Open the EDS for 1734-OB8E and go to the section [Connection Manager], assuming that Connection9 (Exclusive Owner) will be used:

Configure connection settings

Please choose "Connection" in the Navigation Area of the Modular Generic Adapter. Select the Module “Slot<2> 1734-OB8E”.

Decode the fields "trigger & transport" and "realtime format", which are defined in Connection9.

These parameters describe the connection variables, which have to be filled in the Connection configuration Window in Sycon.net.

Open the Tool "EZ-EDS" to decode the parameters.

Open the EDS by selecting "File → Open…”. Select "Generic EDS" as EDS type and ignore the upcoming error messages.

When the file is successfully opened, select “Connection1” in the left tree view.

The name “Connection9” in EDS file is automatically converted to “Connection1”.

Now configure the Connection Area in Sycon.net, based on these informations:

Don't forget, to set the Connection name to "Connection9".

Configure assembly instance ID

Choose "Assembly" in the Navigation Area of the Modular Generic Adapter now. Select the Module “Slot<2> 1734-OB8E”.

Now the Connection Path has to be filled in. The Connection Path is described in the EDS-File:

Switch back to EZ-EDS, select “Connection1” in the left tree view.

Click the Button "Decode Path". A new Window will pop up. Select decimal format in this dialog.

Now the instance ID can be read out for Configuration in Sycon.net.

Based on the above informations, the assembly Instance ID can be specified.

The instance "20 04 24 7B 2C 22 2C 2C" can also be decoded manually as follows:

20 04

24 67

2C 22

2C 2C

Logical Segment,

Class ID 0x04(4)

Configuration path,

instance ID 0x7B (123)

O2T Connection Point,

output Assembly instance ID 0xBE (34)

T2O Connection Point,

input Assembly instance ID 0x04 (44).

Configure Input assembly length

The input assembly length is defined in the field “T->O size” and field “T->O format” of Connection9:

It can be decoded as follows:

T → O

, , Assem127

RPI	Size	Format
empty	empty	Assem127

When the "Size" of the T=>O default description is empty, the "Format" has to be evaluated.

In this case, Assem127 is used to define the format. Go to the definition of Assem127, in the EDS.

Since the field for the length is empty ($ Length in bytes), the Member fields should be evaluated:

The Assemblys Members can be decoded as follows:

,,

32,,

,Assem44;

	Member Size	Member Reference
1st Member	empty	empty
2nd Member	32	empty
3rd Member	empty	Assem44

This means, the first Member is reserved, the second one has a size of 4Byte (32Bit) and the third one references to Assem44.

Go to Assem44:

The "total length in bytes" is defined as "1".

Now the total size of Assem44 can be defined:

	Member Size	Member Reference	Size in Byte
1st Member	empty	empty
2nd Member	32	empty	4
3rd Member	empty	Assem44	1
Total length of Input Assembly Assem127			5

Configure Output assembly length

The output assembly length is defined in the field “O->T size” and field “O->T format” of Connection9:

It can be decoded as follows:

O → T

,,Assem126,

RPI	Size	Format
empty	empty	Assem126

When the "Size" of the O=>T default description is empty, the "Format" has to be evaluated.

In this case, Assem126 is used to define the format. Go to the definition of Assem126, in the EDS.

Since the field for the length is empty ($ Length in bytes), the Member fields fields should be evaluated:

The Assemblys Member can be decoded as follows:

,,

,Assem34;

	Member Size	Member Reference
1st Member	empty	empty
2nd Member	empty	Assem34

This means, the first Member is reserved, the second one references to Assem34.

Go to Assem34:

The "total length in bytes" is defined as "1".

Now the total size of Assem126 can be defined:

	Member Size	Member Reference	Size in Byte
1st Member	empty	empty
2nd Member	empty	Assem34	1
Total length of Input Assembly Assem126			1

Configure configuration assembly length

The configuration assembly length is automatically calculated by the data length of cfg. #1 and cfg. #2 data segment.

The user is not allowed to directly edit this length.

Configure cfg. #1 data segment

The cfg #1 data segment is defined in field "$ config part 1" of Connection9:

Here Assem124 is used to define the format. Go to the definition of Assem124:

In this case, both Values ("Member Size" and "Member Reference") have to be evaluated.

The Assemblys Member informations can be read as follows:

	Member Size	Member Reference
1st Member	16	Param121
2nd Member	16	empty

The field of the first Member indicates, that it has a data length of 16 bit. It also has a Reference to Param121.

Go to the definition of Param121.

The "data size in Byte" defines a size of 2 Byte, with a default value of 1.

So the default data of Param121 is 0x0001.

The user can also define a value between min. value and max. value.

Go back to the definition of Assem124.

The Second Member has a length of 16 and has no Reference entry. This means, all data is defined with value 0.

	Member Size	Member Reference	Data (Hex)	Swap
1st Member	16	Param101	01 00	01 00
2nd Member	16	empty	00 00	00 00
Total				01 00 00 00

Configure cfg. #2 data segment

The cfg #2 data segment is defined in field "$ config part 2" of Connection9:

Here Assem123 is used to define the format. Go to the definition of Assem123:

Please repeate the procedure mentioned in the first data segment for each Member.

For example the first Member:

The Size of this Member is definded with 1Bit and has a Reference to Param43.

The Size is defined with 1Bit (Boolean), the Default Value is 0 (Hex 0000):

When analyzing all Members and Parameters, the following table can be created:

Member	Member Size (Bit / Boolien)	Member Reference	Data (Hex)	Swap
1	1	Param43	0
2	1	Param45	0
3	1	Param47	0
4	1	Param49	0
5	1	Param51	0
6	1	Param53	0
7	1	Param55	0
8	1	Param57	0

9	1	Param44	0
10	1	Param46	0
11	1	Param48	0
12	1	Param50	0
13	1	Param52	0
14	1	Param54	0
15	1	Param56	0
16	1	Param58	0
			00 00	00 00

17	1	Param59	0
18	1	Param61	0
19	1	Param63	0
20	1	Param65	0
21	1	Param67	0
22	1	Param69	0
23	1	Param71	0
24	1	Param73	0

25	1	Param60	0
26	1	Param62	0
27	1	Param64	0
28	1	Param66	0
29	1	Param68	0
30	1	Param70	0
31	1	Param72	0
32	1	Param74	0
			00 00	00 00

33	1	Param83	1
34	1	Param84	1
35	1	Param85	1
36	1	Param86	1
37	1	Param87	1
38	1	Param88	1
39	1	Param89	1
40	1	Param90	1

41	1	Param91	0
42	1	Param92	0
43	1	Param93	0
44	1	Param94	0
45	1	Param95	0
46	1	Param96	0
47	1	Param97	0
48	1	Param98	0
			FF00	00FF

49	1	Param75	0
50	1	Param76	0
51	1	Param77	0
52	1	Param78	0
53	1	Param79	0
54	1	Param80	0
55	1	Param81	0
56	1	Param82	0
			00 00	00 00

Therefore the cfg #2 data segment results in:

0000 0000 FF00 0000

Final assembly configuration of 1734-OB8E

Configure 1734-AENT

Specify Connection

Open the EDS for 1734-AENT and go to the section [Connection Manager], assuming that Connection1 (Exclusive Owner) will be used:

Configure connection settings

Please choose "Connection" in the Navigation Area of the Modular Generic Adapter. Select the Module “Slot<0> 1734-AENT”.

Decode the field "trigger & transport" and "realtime format", which are defined in Connection1.

These parameters describe the connection variables, which have to be filled in the Connection configuration Window in Sycon.net.

Open the Tool "EZ-EDS" to decode the parameters.

Open the EDS by selecting "File → Open…”. Select "Generic EDS" as EDS type and ignore the upcoming error messages.

When the file is successfully opened, select “Connection1” in the left tree view.

Now configure the Connection Area in Sycon.net, based on these informations:

Don't forget, to set the Connection name to "Connection1".

Configure assembly instance ID

Choose "Assembly" in the Navigation Area of the Modular Generic Adapter now. Select the Module “Slot<0> 1734-AENT”.

Now the Connection Path has to be filled in. The Connection Path is described in the EDS-File:

Switch back to EZ-EDS and select “Connection1” in the left tree view.

Click the Button "Decode Path". A new Window will pop up. Select decimal format in this dialog. Now the instance ID can be read out for Configuration in Sycon.net.

Based on the above information, the assembly Instance ID can be specified.

The instance "20 04 24 66 2C 64 2C 65" can also be decoded manually as follows:

20 04

24 66

2C 64

2C 65

Logical Segment,

Class ID 0x04(4)

Configuration path,

instance ID 0x66 (102)

O2T Connection Point,

output Assembly instance ID 0x64 (100)

T2O Connection Point,

input Assembly instance ID 0x65 (101).

Configure Input assembly length

The Input assembly lengts results in the total length of all Modules (in this case the input assembly length of 1734-IB8 + 1734-OB8E).

Since these are already filled in, you can can just summ up the two assemby length 5 + 5 = 10.

Configure Output assembly length

The Input assembly lengts results in the total length of all Modules (in this case the input assembly length of 1734-IB8 + 1734-OB8E).

Since these are already filled in, you can can just summ up the two assemby length 0 + 1 = 1.

Configure configuration assembly length

The configuration assembly length is automatically calculated by the data length of cfg. #1 and cfg. #2 data segment.

The user is not allowed to directly edit this length.

Configure cfg. #1 data segment

The cfg #1 data segment is defined field "$ config part 1" of Connection1:

Since this area is empty, no cfg. #1 data segment has to be defined.

Configure cfg. #2 data segment

The cfg #2 data segment is defined field "$ config part 2" of Connection1:

Here Assem9 is used to define the format. Go to the definition of Assem9:

The Assemblys Member informations can be read as follows:

	Member Size	Member Reference
1st Member	32	1
2nd Member	16	Param 200
3rd Member	8	Param 204
4th Member	8	Param 205
5th Member	8	Param 206
6th Member	8	Param 207

The "data size in Byte" has a size of 2 Byte, with a default value of 1.

Since this describes the Chassis Size, the value should be set to 3 (See parameter description: "Enter the number of I/O modules plus 1 additional slot for the adapter").

So the data of Param200 is 0x0003.

When analyzing all Members and Parameters, the following table can be created:

	Member Size	Member Reference	Data (Hex)	Swap
1st Member	32	1	0000 0001	0100 0000
2nd Member	16	Param 200	00 03	03 00
3rd Member	8	Param 204	00	00
4th Member	8	Param 205	01	01
5th Member	8	Param 206	00	00
6th Member	8	Param 207	01	01
Total				0100 0000 0300 0001 0001

Final assembly configuration of 1734-AENT

Browser not supported