netX USB drivers

Q

Which USB drivers should be installed for netX 90 device?

A

There are two USB drivers available for netX 90.

USB driver for Flasher CLI, which can be used with muhkuh framework, flasher and netX Studio
netX USB FTDI driver, which can be used for netX hardware with FTDI 2232 USB to SPI controller

The following table shows an overview of different driver usages for different devices and applicaiton:

Product	USB ID/Device Name	Port	Applicaiton	USB-Driver and Versions	Driver	Hilscher KB pages	Comments
NXHX 90-JTAG	(Universal Serial Bus Device) NXHX 90-JTAG USB-JTAG (USB-Controller) NXHX 90-JTAG B (Anschlüsse (COM&LPT)) NXHX 90-JTAG USB Serial Port(COMxx)	mini USB (X1000) MI_00= JTAG MI_01=UART	netX Studio CDT / Flasher / netHost (Serial Port)	NXHX90-JTAG USB-JTAG driver (10/16/2018 2.4.7)	bootloader_windows_driver-2.4.7.zip	V2.4.7 Windows USB driver for flasher CLI	ONLY for communication with netX Rom code / bootloader; NOT for communication with 2nd stage loader or firmware ( (Flasher) support for JTAG / UART interface(Marshaller) via FTDI chip
NRPEB H90-RE	Win 7: Hilscher NRPEB-SPM(IF0) Hilscher NRPEB-SPM(IF1) Win 10: NRPEB H90-RE NRPEB H90-RE	USB JTAG SPM (X700)	netHost (SPM) / Device Explorer / Communiction Studio (netX serial DPM via USB/SPI)	netX USB FTDI driver V3.0.0.0	netX USB FTDI driver installation V3.0.0.0.zip	V3.0.0.0 (NXUSBFTDI)	USB driver installation for netX hardware with FTDI 2232 USB to SPI controller. Note: This installaion only supports hardware with JTAG and SPM combinations connected to the FTDI chip. Other combinations like JTAG and COM ports are currently not supported and installed via different installation programs.
ARM-USB-TINY-H (Olimex)	Olimex OpenOCD JTAG ARM-USB-TINY-H (Interface 0) Olimex OpenOCD JTAG ARM-USB-TINY-H (Interface 1)	USB-JTAG	netX Studio CDT	WinUSB 6.1.7600.16385			It is recommended to use a piece of software which simplifies the drivers installation (or the change of drivers), which called Zadig. The Zadig program might be downloaded from here: http://zadig.akeo.ie/
NXJTAG-USB	NXJTAG-USB (Interface 0) NXJTAG-USB (Interface 1)	usb-JTAG	netX Studio CDT / Flasher	NXJTAG-USB USB-JTAG driver USB driver for the netX ROM code	bootloader_windows_driver-2.4.7.zip	V2.4.7 Windows USB driver for flasher CLI	Driver for NXJTAG-USB LibUSB based JTAG interface
NXHX-FTDI	Hilscher NXHX-FTDI (IF0) Hilscher NXHX-FTDI (IF1)	miniUSB on NXHX-FTDI	netHost (SPM) / Device Explorer / Communiction Studio (netX serial DPM via USB/SPI)	netX USB FTDI driver V3.0.0.0	netX USB FTDI driver installation V3.0.0.0.zip	V3.0.0.0 (NXUSBFTDI)	USB driver installation for netX hardware with FTDI 2232 USB to SPI controller

See also...