netX USB drivers

Q

Which USB drivers should be installed for netX 90 device?

A

There are two USB drivers available for netX 90.

  1. USB driver for Flasher CLI, which can be used with muhkuh framework, flasher and netX Studio
  2. netX USB FTDI driver, which can be used for netX hardware with FTDI 2232 USB to SPI controller

The following table shows an overview of different driver usages for different devices and applicaiton:

ProductUSB ID/Device NamePortApplicaitonUSB-Driver and VersionsDriverHilscher KB pagesComments

NXHX 90-JTAG

(Universal Serial Bus Device)
NXHX 90-JTAG USB-JTAG

(USB-Controller)
NXHX 90-JTAG B

(Anschlüsse (COM&LPT))
NXHX 90-JTAG USB Serial Port(COMxx)

mini USB

(X1000)

MI_00= JTAG

MI_01=UART

netX Studio CDT / Flasher / netHost (Serial Port)

NXHX90-JTAG USB-JTAG driver (10/16/2018 2.4.7)

bootloader_windows_driver-2.4.7.zip

V2.4.7 Windows USB driver for flasher CLI



support for JTAG / UART interface via FTDI chip

NRPEB H90-RE

Win 7:

Hilscher NRPEB-SPM(IF0)
Hilscher NRPEB-SPM(IF1)

Win 10:

NRPEB H90-RE
NRPEB H90-RE

USB JTAG SPM (X700)

netHost (SPM) / Device Explorer / Communiction Studio

(netX serial DPM via USB/SPI)

netX USB FTDI driver V3.0.0.0netX USB FTDI driver installation V3.0.0.0.zipV3.0.0.0 (NXUSBFTDI)

USB driver installation for netX hardware with FTDI 2232 USB to SPI controller.

Note:
This installaion only supports hardware with JTAG and SPM combinations connected to the FTDI chip.
Other combinations like JTAG and COM ports are currently not supported and installed via different installation programs.

ARM-USB-TINY-H (Olimex)

Olimex OpenOCD JTAG ARM-USB-TINY-H (Interface 0)

Olimex OpenOCD JTAG ARM-USB-TINY-H (Interface 1)

USB-JTAGnetX Studio CDTWinUSB 6.1.7600.16385

It is recommended to use a piece of software which simplifies the drivers installation (or the change of drivers), which called Zadig.

The Zadig program might be downloaded from here:

http://zadig.akeo.ie/
NXJTAG-USB

NXJTAG-USB (Interface 0)

NXJTAG-USB (Interface 1)

usb-JTAGnetX Studio CDT / Flasher

NXJTAG-USB USB-JTAG driver

USB driver for the netX ROM code

bootloader_windows_driver-2.4.7.zipV2.4.7 Windows USB driver for flasher CLI

Driver for NXJTAG-USB

LibUSB based JTAG interface
NXHX-FTDI

Hilscher NXHX-FTDI (IF0)

Hilscher NXHX-FTDI (IF1)

miniUSB on NXHX-FTDI

netHost (SPM) / Device Explorer / Communiction Studio

(netX serial DPM via USB/SPI)

netX USB FTDI driver V3.0.0.0netX USB FTDI driver installation V3.0.0.0.zipV3.0.0.0 (NXUSBFTDI)USB driver installation for netX hardware with FTDI 2232 USB to SPI controller