Skip to end of banner
Go to start of banner

How can I set a gateway back to factory default settings?

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this content. View the current version.

Compare with Current View Version History

« Previous Version 13 Next »

Q

How can I set a gateway back to factory default settings?

A

The Edge Gateways do not have a physical reset button or any other specific hardware detail to reset them to factory default. Instead an USB stick is needed to initiate to recover the system software.

Attention! Recovering a gateway with the following procedure explained below will clear all existing contents on the device's main storage memory (HDD, eMMC). So before continuing make sure you made a backup using the gateway's management web UI under Control Panel/System/Backup and Restore.

USB stick preparation

  • Use an USB stick with a minimum size of 500Mbyte
  • The stick should be USB 2.0 compatible
  • The stick have to be formatted FAT32
  • The stick's volume have to be named "RECOVERY". Other names will not be accepted.
  • Sticks of sizes >=64GByte can't be formatted FAT32 under Windows. A tool such as "HP USB STICK FORMAT" is needed to format bigger sizes.

Extracting the provided image

  • The system software image comes as zip compressed archive
  • Use a tool such as 7Zip to decompress the file

  • If you open the image you see a structure like this:

  • Extract the whole image to your USB stick's root directory in a 1:1 copy

Installing the system software

  • Switch off the gateway
  • Plug in the USB stick in any of the gateway's USB ports
  • Power on the gateway
  • The gateways loader will recognized the USB stick during boot sequence automatically and initiates the installation
  • Please do not interrupt the installation and wait until the device powers down.
  • Remove the USB stick and restart the gateway

What to do if the installation procedure does not work?

Gateway with a DVI display port (NIOT-E-TIJCX-GB-XX)

  • Make sure the gateway is switched off. The green power LED indicator will be in state "off"
  • Plug in a keyboard in any of the gateway's USB ports
  • Connect a monitor to the gateway's DVI-I display or DP port. Just use a 1:1 DVI/ DP cable only will work (don’t use adapters DP/DVI-I to VGA or so, they will not be recognized by the gateway and the screen remains black)
  • Plug in the firmware stick in any of the available USB ports (USB3.0 is much faster and marked in blue)
  • Power on the gateway
  • The time the gateway beeps with a sound press key DEL on your keyboard. This activates the BIOS configuration screen on your monitor. If you are too late pressing the DEL key reset the gateway and start from beginning.
  • Use the cursors to move to the “Boot” menu item and then move down to “Boot Option #1”. It should be set to “UEFI OS: (P1: xxxxxxxxxx)" which is the HDD
  • Press "enter" to open the other boot options. Choose “UEFI: <name of the stick> xxGB”. DO NOT choose the option "UEFI: Built-in EFI Shell"
  • Move the cursor up to “Save & Exit” and confirm saving with yes. The gateway will reboot automatically and will now start booting from USB stick instead of the HDD
  • During the following boot sequence the gateway will boot from USB stick and initiates the installation
  • Please do not interrupt the installation and wait until the device powers down
  • Remove the USB stick and restart the gateway

Gateway with no display port (NIOT-E-IB100-GB-XX)

  • Make sure the gateway is switched off. The green power LED indicator will be in state "off"
  • Connect a serial cable to the serial RS 232 port to monitor serial console BIOS outputs on a terminal program at settings 11500,8,N,1
  • Plug in the firmware stick in any of the available USB ports (USB3.0 is much faster and marked in blue)
  • Power on the gateway
  • Watch the console output and press key DEL on your keyboard in your terminal program when you the the BIOS start screen. This activates the BIOS configuration screen in your terminal window. If you are too late pressing the DEL key reset the gateway and start from beginning
  • Use the cursors to move to the “Boot” menu item and then move down to “Boot Option #1”. It should be set to “UEFI OS: (P1: xxxxxxxxxx)" which is the eMMC
  • Press "enter" to open the other boot options. Choose “UEFI: <name of the stick> xxGB”. DO NOT choose the option "UEFI: Built-in EFI Shell"
  • Move the cursor up to “Save & Exit” and confirm saving with yes. The gateway will reboot automatically and will now start booting from USB stick instead of the eMMC
  • During the following boot sequence the gateway will boot from USB stick and initiates the installation
  • Please do not interrupt the installation and wait until the device powers down
  • Remove the USB stick and restart the gateway
See also...

  • No labels